Game of Life 32b
This writeup is still in the works! Come back later to get information on all the mean tricks ;) Meanwhile you can download and comment the intro.
Contents
Original version : 65 bytes
We'll start with the old 65 bytes version and bring it down to 32 bytes.
It will help to understand what the core algorithm does, before optimizing it. I will not go into the details of random number generation and key handling since these parts are removed in the final version anyway. Setting up screen mode and putting pixels to the screen is described in the basic sectionn of this Wiki. The core routine computes the [https://en.wikipedia.org/wiki/Conway%27s_Game_of_Life#Rules "normal" game of life rules, but with a twist. Instead of regarding only eight neighbour cells inside a 3x3 neighbourhood , ALL nine cells are taken into consideration, and the rules are reinterpreted as:
- If the number of cells is 3, the center cell will be alive.
- If the number of cells is 4, the center cell keeps its state.
- Otherwise, the cell dies (or stays dead).
Like in other (trivial) implementations, the 2D space is parsed cell by cell, from left to right, and from top to bottom. Since the game of life does not work "in situ" (updating the current cell instantly will lead to wrong results of following calculations), current cells are "marked", and when the calculations are advanced far enough that the cell in question does not influence any calculation of the current iteration, it will be "corrected" by shr [byte di-65],5
to the target value of the next iteration. The summation is as usual, an inner loop, adding up 3 cells of one column, and the outer loop, shifting from right (+1) to the left (-1), thus adding up 9 cells of a 3x3 neighbourhood.
At the start of the loop, there is already the first "trick" happening. The register of summation cl
is not properly cleaned, but at this point it can either contain 0 or 32 from the instruction and al,0x20
after xchg cx,ax
. If an arbitrary amount of cells has this on bit set, that won't hurt the calculation because of a special property of the rcr
instruction. "The processor restricts the count to a number between 0 and 31 by masking all the bits in the count operand except the 5 leastsignificant bits."
When the summation is complete, the aforementioned rcr
is executed, but not before setting the carry flag (stc
) which will be rotated in from the left, and directly right of the original cell value. By extracting the 6th bit of this rotated value (with and al,0x20
we get exactly the value according to the rules defined above.
This value is now set in the original cell with or [si-1],al
, which as shown before, does not hurt the computation, besides the cell value has a temporary value of 32 or 33, thus being visible as brighter blue pixel in the short time span between marking and correction.
; http://read.pudn.com/downloads208/sourcecode/asm/981812/LIFE65.ASM__.htm
; Life simulator, 72 bytes - Vladislav Kaipetsky and Tenie Remmel
; 65 bytes - Mark Andreas
; If no args, regs on startup are:
; AX = BX = 0000h
; SI = IP = 0100h
; DI = SP = FFFEh
IDEAL
MODEL TINY
P386
CODESEG
ORG 100h
Start: int 1ah ; ah=00: cx=hours, dx=tic counter
mov al,13h ; Set mode 13h
int 10h
xchg dx,ax
push 09000h ; DS = last 64K segment
pop ds
push 0A000h ; ES = video memory
pop es
; BX is already zero
RandLoop:
rol ax,1 ; Generate random number
adc [bx],al
dec bx
jnz RandLoop
; BX will not be equal to 3 the first time this loop is executed, but
; it will be for all other times. As SI = 0100h and DI = FFFEh on
; startup, SI - DI will be equal to 258.
LifeLoop:
xchg cx,ax
AccLoop:
add cl,[di+bx-64] ; Add in this column
add cl,[si+bx-2]
add cl,[si+bx+318]
dec bx ; Loop back
jnz AccLoop
mov al,[si] ; Get center cell, set pixel
stosb
stc ; 3 = birth, 4 = stay (tricky):
rcr al,cl ; 1.00?0000x --> 0.0x100?00 (rcr 3)
and al,20h ; ^carry | ^
; +---> 0.00x100?0 (rcr 4)
or [si-1],al ; Add in new cell ^
shr [byte di-65],5 ; Shift previous value
mov bl,3 ; 3 iterations in AccLoop
inc si ; Loop while not zero
jnz LifeLoop
mov ah,1 ; Check for key
int 16h
jz LifeLoop ; Loop if no key
xchg ax,bx ; Set text mode
int 10h
ret ; Return
End Start
Remove key handler and RNG : 44 bytes
In order to reach 32 bytes, all the convenient stuff has to be removed. In case there is space left, parts of it could be reintegrated again. There are tiny changes to make this work as intended. The segment where all the calculation takes place has been changed to 1000h
, pointing to a lower memory location. (Note: this might be working just with DosBox) The activity there (visible on the screen) helps spawning actual game of life structures.
mov al,[si]
and inc si
have been replaced with lodsb
since that saves one byte.
Start:
mov al,13h ; Set mode 13h
int 10h
push 01000h ; DS = low memory segment
pop ds
push 0A000h ; ES = video memory
pop es
; BX is already zero
LifeLoop:
xchg cx,ax
AccLoop:
add cl,[di+bx-64] ; Add in this column
add cl,[si+bx-2]
add cl,[si+bx+318]
dec bx ; Loop back
jnz AccLoop
;mov al,[si] ; Get center cell, set pixel
lodsb
stosb
stc ; 3 = birth, 4 = stay (tricky):
rcr al,cl ; 1.00?0000x --> 0.0x100?00 (rcr 3)
and al,20h ; ^carry | ^
; +---> 0.00x100?0 (rcr 4)
or [si-1],al ; Add in new cell ^
shr [byte di-65],5 ; Shift previous value
mov bl,3 ; 3 iterations in AccLoop
; inc si ; Loop while not zero
jmp short LifeLoop
Switching to Textmode : 38 bytes
Setting up screen mode and pixel access is requiring quite a bit of space, so in this version, it is removed. That is directly punished with an additional byte, because DI
is no longer involved in the process, thus, an optimization had to be removed. The assumption is that the computer this runs on, is already in text mode (40x25 chars, colors). This also helps with the calculation, since now it takes place directly on the screen (only one segment has to be set up) and no content has to be generated initially, since there is always at least something on the screen that works as seed value. A small downside is the alignment of cells, because in textmode, one cell occupies TWO bytes (one for color information). Luckily, the color information is by default set to "gray on black". An additional dec bx
, replacing lodsb
with lodsw
and changing mov bl,3
to mov bl,6
helps fixing the alignment issue. Additionally, the screen address changed (push 0xb800
pop ds
) Another lucky coincident is, that instead of blue pixels, we now have a "smiley char" with orthogonal borders, which is a decent representation of a living cell. Inbetween marking and correction it shortly changes to an exclamation mark (!), which is barely visible.
push 0xb800
pop ds
LifeLoop:
stc ; 3 = birth, 4 = stay (tricky):
rcr al,cl ; 1.00?0000x --> 0.0x100?00 (rcr 3)
and al,20h ; ^carry | ^
or [si-2],al ; Add in new cell ^
shr byte [si-160-6],5 ; Shift previous value
mov bl,6
xchg cx,ax
AccLoop: add cl,[si+bx-160-4] ; Add in this column
add cl,[si+bx-4]
add cl,[si+bx+160-4]
dec bx ; Loop back
dec bx ; Loop back
jnz AccLoop
lodsw
jmp short LifeLoop
Using instructions as segment adress : 36 bytes
Instead of using push
and pop
to get the screen adress, there is also the instruction lds
available, which reads the segment value from memory. A value "close" to 0xb800
would be sufficient, because the visible screen in textmode is just a tiny part of the 64 kilobytes addressable by one segment. The idea is now to reuse parts of the code as segment address, which is possible when the instructions is one of the above. If there is such an instruction, it can start at the 4th byte ([si]
points to the start of the code and lds bx,[si]
puts the first two bytes into BX and the 3rd and 4th into DS, reversed). In this case lodsw
can be reused as the first (higher) byte of the segment. The 3rd byte would be only relevant for alignment, so instead of putting "0x00" there, a one-byte-instruction can be used there. The whole process saves two bytes.
lds bx,[si]
LifeLoop:
stc ; 3 = birth, 4 = stay (tricky):
lodsw
rcr al,cl ; 1.00?0000x --> 0.0x100?00 (rcr 3)
and al,20h ; ^carry | ^
or [si-2],al ; Add in new cell ^
shr byte [si-160-6],5 ; Shift previous value
mov bl,6
xchg cx,ax
AccLoop: add cl,[si+bx-160-4] ; Add in this column
add cl,[si+bx-4]
add cl,[si+bx+160-4]
dec bx ; Loop back
dec bx ; Loop back
jnz AccLoop
jmp short LifeLoop